Yes, professional painters clean walls before painting. It is not a courtesy step. It is a written requirement in the coating manufacturer’s specification, and skipping it is the fastest way to make a good product fail. Sherwin-Williams states that a surface must be dry and sound, with mildew, oil, dust, dirt, loose rust, and peeling paint removed to get good adhesion.
What gets used depends on the surface. Kitchen and shop walls need a degreaser. Mildew needs a bleach solution, not soap. Chalky exterior paint has to be washed before any topcoat goes on. Glossy trim needs washing and then dulling, because clean gloss still will not hold paint.
Below is what painters actually remove, the method for each surface, and how to tell whether a crew really did it.
Why Cleaning Is a Requirement and Not a Preference
Paint bonds to the surface it touches. If that surface is a layer of grease, dust, or chalk, the paint bonds to the contamination instead of the wall.
Manufacturers write this into their specifications in plain terms. Sherwin-Williams spells it out for previously coated surfaces. Oil, grease, loose paint, mill scale, dirt, rust, mold, mildew, mortar, efflorescence, and sealers all have to come off first. Only then does the new coat bond soundly to the old paint underneath. That is a specification, not advice.
The practical consequence is a warranty issue. A coating warranty covers the product performing as designed. Applied over a contaminated surface, any failure traces to the application rather than the paint, and the claim goes nowhere. That is why a serious commercial painting proposal spells out the cleaning method by surface rather than writing prep as needed.
What Painters Are Actually Washing Off
Different buildings collect different problems. Knowing which one you have tells you what the crew should be doing.
| What Gets Washed Off | Where It Comes From | What Happens If You Paint Over It |
|---|---|---|
| Grease and cooking oil | Kitchens, break rooms, restaurants, shop areas | The paint never bonds, then peels away in sheets |
| Mildew and mold | Bathrooms, shaded exteriors, damp basements | Growth continues under the film and bleeds back through |
| Chalk | Weathered exterior paint, especially older alkyd | The new coat sits on loose powder instead of the substrate |
| Hand oils and scuffs | Corridors, doorways, switch plates, stair rails | Flashing and adhesion failure right where hands land |
| Dust and drywall sanding residue | New construction and every patched area | The film bonds to dust rather than to the wall |
| Nicotine and smoke residue | Older apartments, bars, former smoking areas | Brown staining bleeds through even two finish coats |
| Form release agents and laitance | New poured concrete and block | The coating lifts off the slab in sheets |
| Factory oils on galvanized metal | New railings, downspouts, metal panels | Early failure, because the zinc oil was never removed |
That last row surprises people. Sherwin-Williams explains that galvanized metal arrives with oils applied at the factory to stop the zinc from oxidizing. If the metal cannot weather for six months, those oils have to be removed with a solvent or a water-soluble degreaser before any coating goes on.
How the Cleaning Method Changes by Surface
There is no single wall-washing step that covers a whole building. Each substrate has its own method, and several are governed by published standards.
| Surface | Cleaning Method | The Standard or Detail Behind It |
|---|---|---|
| Painted drywall and plaster | Wash with detergent or degreaser, then rinse | Rinsing matters, because detergent film blocks adhesion too |
| Bare or new concrete and block | Broom, vacuum, air blast, water, or steam cleaning | Sherwin-Williams points to ASTM D4258 for these methods |
| Bare or previously coated steel | Solvent cleaning to remove oil, grease, and oxide | Sherwin-Williams specifies SSPC-SP1, Solvent Cleaning |
| Galvanized metal | Water-soluble degreasing cleaner on a cloth or sponge | Change cloth and solution often so oil comes off, not around |
| Mildewed surfaces | One part household bleach to three parts warm water | Scrub, wait 10 minutes, rinse, then dry 48 hours before paint |
| Chalky exterior paint | Wash until the chalky feel is gone | Sherwin-Williams says any chalky surface must be cleaned first |
| Glossy old paint | Wash clean, then dull it by sanding or abrasive cleanser | Washing alone leaves a surface paint cannot grip |
| Wallpapered walls | Strip the paper, then wash off the old adhesive and rinse | Let the wall dry fully before priming |
Soft or powdery plaster gets its own treatment. Sherwin-Williams recommends one pint of household vinegar in one gallon of water. Repeat the treatment until the surface hardens, then rinse with plain water and let it dry before priming.
New concrete needs patience on top of cleaning. Beyond removing laitance, dust, form release agents, and curing membranes, Sherwin-Williams calls for concrete and mortar to cure at least 30 days at 75 degrees before coating.
Why Mildew Needs Bleach and Not Soap
This is the mistake that produces the most callbacks, and it happens on both residential and commercial jobs.
Detergent removes the stain. It does not kill the organism. Wash mildew with soap, paint over it, and the growth keeps working under the film until it bleeds through the new coat.
Sherwin-Williams publishes the method. Mix one part liquid household bleach with three parts warm water. Apply it and scrub the affected area. Leave the solution on the surface for about 10 minutes. Rinse thoroughly with clean water, then let the surface dry for 48 hours before painting. The company adds two warnings worth repeating. Never add detergent or ammonia to a bleach and water mix, and wear eye protection, waterproof gloves, and covered skin.
That 48-hour drying window is the part crews under pressure tend to skip. A wall that looks dry can still hold moisture that will blister the coating from behind.
Why Clean Is Not the Same as Ready
Two surfaces will fail even after a thorough washing, and both are common.
Glossy paint. Sherwin-Williams is direct that glossy old films must be clean and dull before repainting. Washing handles the clean half. The dull half takes sanding, or an abrasive cleanser that does both in one pass. A spotless semi-gloss door still gives new paint nothing to grip.
Chalky exterior paint. Chalking is the old binder breaking down into powder. Any surface with a chalky feel has to be washed until that powder is gone, and heavy chalking may also call for a bonding primer. Paint applied over chalk is bonded to dust.
The same logic covers efflorescence on masonry and rust on steel. Cleaning removes what sits on top. It does not fix a surface whose condition is the problem, which is why prep is a sequence of steps rather than one wash.
How to Tell Whether a Crew Actually Cleaned
You do not have to watch every hour to know.
- Ask for the cleaning method by surface in the written proposal, not the word prep
- Ask which cleaner or degreaser will be used, by product name
- Look for the wash before it happens, since cleaning comes first and leaves the walls visibly wetted
- Run a hand along an exterior wall after washing, and check for chalk on your palm
- Check that mildewed areas sat for a day or two between washing and painting
- Ask what they plan to do about gloss on trim, doors, and railings
- On new concrete, ask how long the slab has cured
A contractor doing this properly will answer all seven without hesitating. The answers also tell you whether the schedule you were quoted actually has room for the work. Prep should run roughly a third to half of the total job on both residential painting and commercial projects.
Final Thoughts
Yes, professional painters clean walls first, and the good ones treat it as the part of the job that determines how long the finish lasts. Grease, mildew, chalk, dust, and factory oils each need a different method, and manufacturer specifications name most of them directly.
The short version for anyone comparing bids. A proposal that lists the cleaner and the method by surface is describing real work. A proposal that says surfaces will be prepped as needed is describing whatever the crew feels like doing on the day.
Anderson Pro Painting has painted homes and buildings across Central Pennsylvania since 2005, and every proposal names the prep steps surface by surface. Our answers to common questions cover what happens before the first coat goes on. Want a painting company in Central Pennsylvania that puts the cleaning method in writing? Request a free estimate. We will walk the surfaces with you before quoting a commercial repaint.



